Search Results

Search Again
Page 5 of 9
  1. mavgrab302
    Post

    Vintage Maverick/Comet photos

    I worked for Zayre for over 10 years... Cool pic's...
    Post by: mavgrab302, Apr 28, 2014 in forum: General Maverick/Comet
  2. mavgrab302
    Post

    76 Maverick Stallion.....

    It looks great... I'll be watching for your next project...
    Post by: mavgrab302, Apr 28, 2014 in forum: Maverick/Comet Projects
  3. mavgrab302
    Post

    What did you do to your Maverick or Comet today

    Installed the engine and t5 (Thanks for the help Jim). Now I have to adjust the cross member so the t5 sits at the proper angle. The headers gave...
    Post by: mavgrab302, Apr 28, 2014 in forum: General Maverick/Comet
  4. mavgrab302
    Post

    HI Guys!

    :Welcome:from Florida........
    Post by: mavgrab302, Apr 26, 2014 in forum: New Members Forum
  5. mavgrab302
    Post

    What did you do to your Maverick or Comet today

    way to confuse me Frank...lol... If I understand it right, I should measure the pinion angle at the rear and set the trans opposite IE: if the...
    Post by: mavgrab302, Apr 25, 2014 in forum: General Maverick/Comet
  6. mavgrab302
    Post

    What did you do to your Maverick or Comet today

    I will check it,thanks... I was told to put a level on the intake and get it as close to level as I can, is this right or is there a certain...
    Post by: mavgrab302, Apr 25, 2014 in forum: General Maverick/Comet
  7. mavgrab302
    Post

    What did you do to your Maverick or Comet today

    I got a hold of a modern driveline t5 cross member for a 67/73 mustang. I've been curious for awhile now wanting to see if it would fit. Well I...
    Post by: mavgrab302, Apr 24, 2014 in forum: General Maverick/Comet
  8. mavgrab302
    Post

    NMRA Coyote-engined Mav Grabber

    Great looking car...
    Post by: mavgrab302, Apr 23, 2014 in forum: Mavericks/Comets in the Movies and Other Media
  9. mavgrab302
    Post

    new member n missouri

    :Welcome:from Florida....
    Post by: mavgrab302, Apr 22, 2014 in forum: New Members Forum
  10. mavgrab302
    Post

    What did you do to your Maverick or Comet today

    I took my engine off the stand and installed the pilot bearing,flywheel,clutch,bell housing and clutch fork... As for the pilot bearing I was a...
    Post by: mavgrab302, Apr 21, 2014 in forum: General Maverick/Comet
  11. mavgrab302
    Post

    New member in Florida

    :Welcome:from Ocala,Florida.......
    Post by: mavgrab302, Apr 20, 2014 in forum: New Members Forum
  12. mavgrab302
    Post

    1972 Comet Build

    Looking good....
    Post by: mavgrab302, Apr 20, 2014 in forum: Maverick/Comet Projects
  13. mavgrab302
    Post

    Pertronix Flame Thrower Drive gear

    I must have got an idiot when I called Pretronix, They told me I would have to buy a steel gear because all theirs were cast iron... I really...
    Post by: mavgrab302, Apr 20, 2014 in forum: Technical
  14. mavgrab302
    Post

    removed headliner

    Make sure you mark all your bows, so can put them back in the same place... they only work in one spot... Now is the time to think about seat...
    Post by: mavgrab302, Apr 20, 2014 in forum: Technical
  15. mavgrab302
    Post

    Motor Mounts, 76 Comet 302?

    Just go to any part store and ask for v8 mounts for 71 and up maverick.. I got mine at autozone...
    Post by: mavgrab302, Apr 19, 2014 in forum: General Maverick/Comet
  16. mavgrab302
    Post

    Seat ID help ??

    Those seats look comfy...
    Post by: mavgrab302, Apr 18, 2014 in forum: Parts Interchange
  17. mavgrab302
    Post

    Pertronix Flame Thrower Drive gear

    I called pertronix because I needed a steel gear for my roller 5.0 They told me none of their distributors have a steel gear... They told me all...
    Post by: mavgrab302, Apr 18, 2014 in forum: Technical
  18. mavgrab302
    Post

    4 speed toploader install update

    Thanks, I will check it out...
    Post by: mavgrab302, Apr 18, 2014 in forum: Technical
  19. mavgrab302
    Post

    4 speed toploader install update

    http://www.rosehillperformanceparts.com/ Yes this is the kit I used.. Scroll down you will see The external slave bracket and the master firewall...
    Post by: mavgrab302, Apr 17, 2014 in forum: Technical
  20. mavgrab302
    Post

    4 speed toploader install update

    I don't have any fluid in mine yet, but the 1/4 inch plate that rosehill supplied for the inside seems to tighten it up pretty good.. My pedal...
    Post by: mavgrab302, Apr 16, 2014 in forum: Technical
Showing results 81 to 100 of 166 Next >
Search Again
Page 5 of 9